REPLACEMENT PARTS
To keep your IC burner operating like new and at peak performance, insist on genuine Industrial Combustion parts. “Non-genuine” or imitation parts can compromise the operation and integrity of your burner and boiler systems.
GAS TRAINS
Siemens Ventless Gas Trains
Siemens Ventless Gas Trains have become the industry standard. We carry a full line of ventless gas trains, both pre-piped and loose components.
In-Stock at Wymbs:
1-1/2″ Siemens Gas Trains fully assembled
2″ Siemens Gas Trains fully assembled
3″ Siemens Gas Trains fully assembled
- 4″ Siemens Gas Trains fully assembled
VGD20 & VGD40 Gas Valves
- SKP15 & SKP25 Actuators
- QPL Pressure Switches (low pressure switches both auto reset and manual reset)
QPH Pressure Switches (high pressure switches both auto reset and manual reset)
- LDU11 Valve Proving System
When you buy a Siemens train from Wymbs, you are gaining access to our technical support. We will assist you with any problems installing and setting up the train. We also provide a wiring diagram for the burner included in the cost of the train.
GAS BOOSTERS
Eclipse HB Series Gas Boosters
Eclipse Hermetic Gas Boosters are UL listed for use on natural and manufactured gas.
These gas boosters are used to increase low inlet gas pressure up to higher levels as required by boilers and process equipment. They deliver the gas at any volume within their capacity range with a relatively constant pressure boost.
The motor and fan are enclosed in a sealed steel casing which includes the wires in the conduit, to prevent gas from leaking into the surrounding environment.
Eclipse HB Series:
Hermetically sealed gas boosters
U.L. listed single stage design
Internally mounted explosion proof motor
Capacities from 2 – 100,000 CFH with differential pressures to 38″ W.C.
Approved for installation by NYC DOB, Con Edison, and National Grid
Optional epoxy coating on all internal surfaces protects against mixtures that contain corrosive compounds.
Eclipse HB Series Applications:
- The utility’s guaranteed gas service pressure is lower than the specified pressures required by boilers or appliances. The Eclipse series HB boosts the incoming gas pressure to allow full and safe operation of all installed gas fired equipment.
A facility benefits economically with a utility contract allowing curtailment of the natural gas supply. The series HB prevents down time as part of a standby system where it can deliver a substitute propane-air mixture.
The Eclipse series HB can deliver an air-gas mixture to premix burners.
A facility where the distribution piping is lengthy and under-sized creates a large pressure drop that results in limited operation. The series HB restores production to full rated capacity.
- Alternative fuels produced by anaerobic digestion, commonly known as sour gas or bio-gas, are collected at landfill or wastewater treatment plants in high volumes but at very low pressures. The series HB boosts these fuels for use in burners or engines for heating, pumping, and cogeneration.
SIEMENS LMV
LMV Linkageless Burner Management
Wymbs Inc has been supplying Siemens LMV systems for many years to simplify burner design and make the production process, mounting and service work more efficient.
If you are retrofitting an existing burner or need a new burner with a Linkageless Burner Management System we can help you. For a new burner, we can have your burner custom built with a Siemens LMV51 or Siemens LMV52 mounted in the panel.
For an existing burner, we have two options. We can have a replacement burner panel built at our factory with the Siemens LMV51 or Siemens LMV52 control mounted and wired in the panel, or we can provide you with all the components necessary for you to field mount and wire the Siemens LMV in the existing panel.
In-Stock at Wymbs:
- LMV51 Control Unit
- LMV52 Control Unit
SQM45 Actuator
SQM48 Actuator
AZL52 Display Module
QRI2 Flame Detector
- Can Bus Cable and Connectors
- Couplings
As with our burners, when you buy your Siemens LMV at Wymbs, you get full access to our technical support team. Technicians are available to meet the contractor on the job to troubleshoot any issues the contractor cannot resolve. We stock a full line of replacement parts in our warehouse and as a Siemens distributor, we can get any Siemens part you need within a few days.
Siemens LMV51 Features:
- Linkage control
- Burner flame safeguard
- Modulating PID control
Can be wired to 4 actuators, controls 3 actuators simultaneously
Siemens LMV52 Features:
- Linkage control
- Burner flame safeguard
- Modulating PID control
Optional O2 trim and/or VFD control
Can be wired to 6 actuators, controls 5 actuators simultaneously for optimal efficiency in low NOx burner applications
Wymbs has partnered with Siemens to offer training classes. If you have mechanics looking for training on the Siemens LMV Linkageless Burner Management System, please contact us for details on the next training class.
DUPLEX PUMPS
Industrial Combustion Oil Pump Systems
Industrial Combustion Simplex and Duplex Oil Pump Systems are designed to deliver No. 2 thru No. 6 fuel oil to any operation which requires an oil supply.
The duplex system assures a constant supply of filtered oil with the second pump available for standby service. This type of service is essential in applications where systems cannot be interrupted to clean strainers or service pump.
The Duplex Oil Pump Systems are assembled, wired and tested units suitable for light or heavy fuel oil. Capacities range from 75 to 1600 gallons per hour.
Industrial Combustion Oil Pump Systems:
- Simplex and Duplex technology
- 75 – 1,600 GPH Capacity
- No. 2 – No. 6 Oil
Packaged systems are assembled, wired and tested for light or heavy fuel oil
- Mounted on a welded drip pan steel base
Pump rating is based on 50 psi discharge pressure. Please consult the Industrial Combustion factory for all available pressures.
Simplex and Duplex No. 2 thru No. 6 Oil:
- Capacities range from 75 to 1600 gallons per hour
- Direct drive gear pumps, with internal relief valves are used for No. 2 and 5 oils
- Screw type pumps with separate relief valves are used for No. 6 oil systems
Pump rating is based on 50 psi discharge pressure, other pressures are available
- Suction should not exceed 15 inches Hg vacuum
All pumps incorporate mechanical seals and are driven by an open drip proof motor or an optional TEFC motor
Standard Equipment:
- Control panel mounted to base
- Motor starter
- Simplex strainers
- Vacuum gauge with isolator (suction side)
Pressure gauge with isolator (discharge side)
- Pump relief valves (integral on No. 2-5 oil)
FIREYE FLAME SAFEGUARDS
Wymbs Inc has been supplying its Industrial Combustion burners with Fireye Flame Safeguards for many years.
Stock burners in our inventory come standard with the Fireye BurnerLogix Flame Safeguard (YB110).
We can also special order your burner with a Fireye Parallel Positioning Control, either a PPC4000 or a PPC6000.
We carry a full inventory of replacement Fireye Controls including the Flame-Monitor E110, BurnerLogix YB100 and all accessories for these flame safeguards.
Fireye Flame Safeguards available:
- BurnerLogix YB110 Flame Safeguard
- YP100 programmer for BurnerLogix YB110
- BLL510 display for BurnerLogix YB110
- YZ300 Interlock annunciator for BurnerLogix YB110
Wiring base for YB110 Flame Safeguard
- Flame-Monitor E110 Flame Safeguard Chassis
- EP160 programmer for E110
- EP260 progammer for E110
- E1R1 amplifier for E110
- EUV1 amplifier for E110
- E300 expansion module for E110
- ED510 display module for E110
- Wiring base for E110
- 48PT2 scanners
Please call us for any other Fireye product not listed.
FIREYE PARALLEL POSITIONING
While we do not stock burners with Fireye Parallel Positioning Controls, we can special order any burner with a Fireye Parallel Positioning Control.
We can also have a retrofit panel made with Fireye Parallel Positioning Controls to convert an existing burner to Parallel Positioning.
Fireye Parallel Positioning components: (Nexus)
- Nexus PPC4000 Parallel Positioning Control
- NXD410 display module for Nexus PPC4000
- FX04 Servo motor for Nexus PPC 4000
- FX20 Servo motor for Nexus PPC 4000
- FX50 Servo motor for Nexus PPC 4000
- Nexus PPC6000 Parallel Positioning Control
- NX6220 display module for Nexus PPC6000
- NXC12 servo motor for PPC6000
- NXC20 servo motor for PPC6000
- NXC04 servo motor for PPC6000
HONEYWELL FLAME SAFEGUARDS
Wymbs Inc can supply you with an Industrial Combustion burner equipped with Honeywell Flame Safeguards. 7800 SERIES works on a wide range of industrial applications: burners, boilers, furnaces, ovens, kilns, process heaters and more.
Every burner we sell can be ordered with a Honeywell RM7800L or any other Honeywell control. 7800 SERIES replaces more than 400 Honeywell and competitive control types.
We can also special order your burner with a Honeywell Parallel Positioning Control, either ControLinks or Slate.
We carry a full inventory of replacement Honeywell Controls and can order any part we don’t have in stock.
7800 SERIES Burner Control:
7800 SERIES Burner Control is the latest in Flame Safeguard state-of-the-art technology.
Honeywell 7800 SERIES combines safety, comprehensive diagnostics, communication and networking capabilities into one compact and affordable microcomputer burner control.
It can do just about anything and everything you would like it to do.
Honeywell Flame Safeguards available:
- RM7800L1087 Flame Safeguard
- S7800A1142 Display
- ST7800A1039 Purge Timer Card
- R7852 Amplifier
- C7915A1028 IR Flame Detector
- Q7800 Subbase
Call us for questions on any Honeywell components, or check out our Legacy Products page.
CONTACT US
Our factory trained technicians are ready to help over the phone or meet you on the job.
PHONE
718-295-3500
joe@wymbs.com
BUSINESS HOURS